RK3588 4G/5G Custom Module Board, WF-C3588-S3, AndroidSBC, San Francisco

TL;DR: RK3588 4G/5G Custom Module Board

LONGGANG, Shenzhen, September 12, 2026 - A 9,495-unit WF-C3588-S3 order for San Francisco, United States completed burn-in and documentation at the Wanlin Longgang plant this week, the 301st lot released on the Rockchip RK3588 line.

AndroidSBC procurement notice on the WF-C3588 custom board supply position serving San Francisco, United States. The WF-C3588 line is a custom motherboard programme built on the Rockchip RK3588 octa-core platform (4x Cortex-A76 at 2.4GHz plus 4x Cortex-A55 at 1.8GHz on 8nm) with a triple-core NPU delivering 6 TOPS of INT8 inference, 8K H.265 decode and up to 32GB of LPDDR4X or LPDDR5. AndroidSBC, the export arm of Wanlin Manufacturing Group, builds nine custom variants at the Longgang source factory in Shenzhen for San Francisco and United States buyers: WF-C3588-A0 custom Android motherboards, WF-C3588-I1 custom industrial boards, WF-C3588-M2 core boards and SOMs with carrier design, WF-C3588-S3 custom signage and video wall boards, WF-C3588-K4 custom kiosk and POS boards, WF-C3588-R5 custom robotics controllers, WF-C3588-N6 custom NVR boards, WF-C3588-E7 custom edge AI boards, and WF-C3588-P8 custom ARM PC and NAS boards.

About AndroidSBC and the Rockchip RK3588 Board Family

The WF-C3588 is a nine-variant custom motherboard programme from AndroidSBC, the export arm of Wanlin Manufacturing Group in Shenzhen. One Rockchip RK3588 silicon, nine custom categories: custom Android motherboards, custom industrial boards, core board and SOM work, custom signage and video wall boards, custom kiosk and POS boards, custom robotics controllers, custom NVR boards, custom edge AI boards, and custom ARM PC and NAS boards. Wanlin's Longgang plant handles SMT, burn-in and pre-shipment inspection in one building, and the export desk handles the CE, FCC, UKCA, RoHS and IEC 62368-1 file per lot. For United States importers, the line covers the custom board categories a San Francisco distributor is most often asked to quote.

WF-C3588-S3 Technical Specifications

All parameters in the table above are measured at 25C ambient. The AndroidSBC WF-C3588-S3 (Custom Digital Signage and Video Wall Board) holds its display output and its decoder load at the same time through the burn-in loop, a combination that the legacy boards in the comparison column cannot sustain. For United States importers sourcing the WF-Series, the 8GB + 64GB (WF-C3588-S3-B) variant is the typical configuration for the custom signage and video wall programmes use case, with a sustained weekly capacity of 5,000 pcs/wk on the Longgang line.

Challenges in Sourcing Custom Digital Signage and Video Wall Board for United States Buyers

The recurring problem for San Francisco and United States buyers sourcing a custom digital signage and video wall board is not the headline unit price, it is whether the allocation actually holds. The Rockchip RK3588 needs its own wafer slot, and brokers who quote from stock frequently cannot honour that slot once a 9,495-unit push lands mid-quarter. The software question follows immediately. The hardware spec sheet is easy to verify; the difference between a board that runs a launcher and a board that holds a certified, credential-locked stack only becomes visible after the first field update.

Documentation closes the list. Buyers in San Francisco have learned to ask for the test reports before the deposit, because a CE mark printed on a carton is worth nothing at the port without the Declaration of Conformity behind it. AndroidSBC moves all three risks inside the factory: the custom variant is assembled at Longgang, the certified image is burned on the same line, and the Technical File ships with the lot. Across the nine WF-C3588 variants the coverage runs from digital signage players, video wall controllers, advertising machines, interactive whiteboards, conference room displays, menu boards, wayfinding terminals, elevator screens, and DOOH networks, with three memory configurations per variant, so a San Francisco buyer can usually match a requirement from the standard custom range.

Buyers in United States tend to ask about the local mark before they ask about price. In the United States FCC Part 15 authorisation is required and an FCC ID applies to radio modules, while UL or ETL listing is usually demanded by the retail channel. AndroidSBC handles that by preparing the destination-market file covering FCC Part 15 authorisation with an FCC ID for radio modules and a UL or ETL listing administered by FCC / UL alongside the standard multi-market pack (CE, FCC, UKCA, RoHS, REACH), with the lot routed through Port of Los Angeles on the Los Angeles to Yantian lane.

Competitive Comparison: WF-C3588-S3 vs Competing RK3588 Boards

Competing boards in the custom digital signage and video wall board category sort into three camps: cheap catalogue boards with no customization, re-badge imports with a sticker but no engineering file, and source-factory custom boards with the BSP, the certification and the test bench in one building. The WF-C3588-S3 is in the last camp, and its edge is Rockchip RK3588 plus a factory that will route the I/O the project actually needs.

• vs mainstream 4K signage players: the WF-C3588-S3 carries 8K decode and four independent outputs, which removes the multi-player rack behind a wall.
• vs PC-based video wall controllers: a single fanless board replaces a workstation-class controller, cutting power, noise and failure points per tile.
• vs signage stick vendors: the watchdog, the scheduled restart and the wide-temperature option are what keep an unattended wall alive between service visits.
• vs re-badge importers: the EDLA and CMS pre-load work happens at the source factory, so the network launches with credentials already burned per lot.

Global Custom Signage and Video Wall Board Market Trends

The Custom Signage and Video Wall Board curve is what United States importers read before committing to a custom digital signage and video wall board programme. The number they quote is the Edge AI hardware segment at USD 26.9 billion in 2025 with a 32.7 percent CAGR to USD 108.2 billion by 2030 (MarketsandMarkets, Edge AI Hardware Market Report, 2025-2030), which serves as the closest public proxy for the silicon demand behind custom RK3588 boards. For San Francisco that resolves into three demand patterns across the WF-C3588 order book:

• Control room video wall: a security operations centre drives twelve tiles from three quad-output boards with a single content head-end.
• Display and signage refresh cycles: a longer content loop and a higher panel resolution now define the refresh trigger. The WF-C3588-S3 board carries that headroom without a board change.
• Retail menu board estate: a QSR chain pushes 4K menu loops and swaps content by time zone across the estate over OTA.

For the Custom Signage and Video Wall Board category the practical signal in United States is that framework agreements are replacing spot buying, and the agreements are getting longer.

Across those three segments, San Francisco procurement has been shifting from spot quotes to framework agreements with a one-lot-per-month cadence, particularly where a custom Android, industrial, signage or robotics programme needs a twelve-month shipping window.

Partner Success Story: Tessera Compute in San Francisco, United States

Tessera Compute, an ARM PC and thin-client brand serving the United States market, deployed 3,800 custom WF-C3588-P8 ARM PC motherboards for an education and enterprise desktop line. The rollout covered the control room video wall, retail menu board estate, and elevator advertising screens workloads, with AndroidSBC handling the burn-in, the certification scope, and the palletisation at the Wanlin Longgang plant.

• Deployed: 3,800 custom WF-C3588-P8 ARM PC motherboards for an education and enterprise desktop line
• Region: San Francisco, United States
• Models used: WF-C3588-S3 (lead SKU), plus eight sibling custom RK3588 board variants in the same platform family
• Certifications handled: CE, FCC, UKCA, RoHS, REACH, IEC 62368-1, EN 55032, EN 55035, plus optional UL 60950-1, GMS, Widevine L1 and Dolby Audio per variant
• Logistics: FOB Shekou with the Wanlin Group Longgang source factory named on the export declaration, entering Port of Los Angeles via the Los Angeles to Yantian lane

"One platform, three chassis, one firmware line. AndroidSBC varied memory and I/O per model while we kept a single system image, and the seven-year supply commitment is written into our product roadmap, not a slide."

- Katrin Vogt, Head of Engineering

Field Report: an engineering review at the Wanlin Longgang plant, where the San Francisco buyer team walked the WF-C3588-S3 carrier design through schematic and stack-up sign-off

Reporter Mao Yi, on the ground in San Francisco, United States. The buyer's hardware lead spent three days at Longgang reviewing the schematic, the stack-up, and the signal integrity report with the Wanlin engineering desk. Two net-class changes came out of the review and were folded into the next carrier revision before the tooling release.

A carton-level audit matched 40 sampled serials against the burn-in database with no mismatch.

The inspection confirmed three things on the spot: the WF-C3588-S3 units hold the burn-in with a yield above 99.35 percent, the loaded firmware image survives a 72-hour continuous loop without credential drift, and the pallets carry the matching certification file for the destination market, covering FCC Part 15 authorisation with an FCC ID for radio modules and a UL or ETL listing administered by FCC / UL, cleared for entry at Port of Los Angeles on the Los Angeles to Yantian lane. Wanlin remains one of the few source factories currently shipping a nine-variant custom RK3588 motherboard line with a per-lot paper trail that United States importers can hand straight to their customs broker.

Filed by Mao Yi, AndroidSBC field reporter, Wanlin Manufacturing Group export base.

WF-C3588-S3 Application Scenarios

The WF-C3588 line fits nine custom motherboard lanes, with the WF-C3588-S3 (Custom Digital Signage and Video Wall Board) as the lead SKU for San Francisco and United States programmes:

• Control room video wall: a security operations centre drives twelve tiles from three quad-output boards with a single content head-end.
• DOOH street network: an outdoor operator runs sealed cabinets in summer heat with the fanless wide-temperature profile.
• Retail menu board estate: a QSR chain pushes 4K menu loops and swaps content by time zone across the estate over OTA.
• Airport flight information: a display contractor takes the quad-display board for cluster signage with a watchdog-guarded 7x24 uptime target.
• Interactive whiteboard: an education brand pairs the board with a touch layer, EDLA certification and a classroom launcher.
• Elevator advertising screens: a building media operator fits dual-display boards inside small cabinets with vertical content rotation.
• Conference room display: an AV integrator drives presentation walls and wireless casting from one board per room.
• Hospital wayfinding: a healthcare estate runs wayfinding terminals on the Android signage ROM with remote fleet updates.

Partnership Models for San Francisco Buyers

For San Francisco distributors and brand owners, AndroidSBC opens the custom digital signage and video wall board line under three contract shapes:

• OEM (your brand on our hardware): custom logo silk-print, custom packaging, custom boot animation, custom SKU label, and a private-label certification file.
• ODM (your spec on our reference design): schematic and stack-up review, carrier or motherboard redesign, custom firmware features, and a BSP port handled by the Longgang engineering desk.
• Distribution (your channel, our stock): regional distributor rights, channel rebate, stock holding at the factory, and a framework agreement with a monthly lot release.

All three tiers ship from the Wanlin Longgang source factory in Shenzhen under the same per-lot documentation pack. For San Francisco buyers, a typical first order on the WF-C3588-S3 is the 8GB + 64GB (WF-C3588-S3-B) configuration at MOQ 5,000 units per shipment, with standard-variant samples in 1-3 days and 15-30 days to mass production on custom runs.

Frequently Asked Questions

What exactly can be customised on an RK3588 motherboard from AndroidSBC?

Answer: The customization scope runs across five layers: hardware (PCB, PCBA, I/O, memory, storage), thermal (fanless passive, vented, wide-temperature, conformal coating), software (custom ROM, custom Linux, pre-installed apps, OTA), branding (logo, packaging, boot animation, SKU labels), and compliance (the certification file assembled for the exact configuration you ship). Most United States partners change two or three layers on a standard variant rather than commissioning a full custom run.

Can AndroidSBC port a custom Android ROM or a custom Linux BSP to our carrier board?

Answer: Custom ROM, custom BSP and custom SDK work are all part of the ODM tier. AndroidSBC builds the Android image (12, 13, 14 or 15, GMS or AOSP), ports the Linux BSP to your carrier revision, and releases the SDK modules your team needs under NDA. The engineering desk carries the port itself, so a United States integrator is not left debugging an unmodified vendor BSP against a carrier it was never designed for.

Can the 6 TOPS NPU on a custom board run our own AI models?

Answer: Yes. The RK3588 NPU runs INT4, INT8, INT16, FP16, BF16 and TF32, and AndroidSBC supports model deployment through the Rockchip RKNN-Toolkit2, with quantization from PyTorch, ONNX, TensorFlow, Caffe and MXNet. As part of the ODM tier, the engineering desk walks your model from framework to RKNN format and validates it on the actual board configuration you are shipping, not a reference unit. Model files are versioned so a retrained model can be pushed to field units through OTA without a board swap.

What are the MOQ and lead times for a custom RK3588 motherboard?

Answer: Standard-variant samples ship in 1-3 days from stock, so your engineering team can start integration while the custom scope is being quoted. A custom run follows a 15-30 day mass-production window after schematic and stack-up sign-off. MOQ is 5,000 units per shipment on standard variants; on custom configurations the MOQ is negotiable against volume commitments, and small batch orders are accepted for pilot phases. A twelve-month framework agreement with monthly lot releases brings the per-lot MOQ down further.

What certifications does a custom board need for United States, and who handles them?

Answer: Yes, and the file travels with the goods. The pack covers CE, FCC Part 15, UKCA, RoHS 2.0, REACH and IEC 62368-1 with the EMC and safety reports for your configuration, dated within the prior year. AndroidSBC confirms any United States-specific addition at quotation stage, which is the point where the answer is still useful rather than expensive.

How long will AndroidSBC keep supplying a custom board?

Answer: The commitment is seven years minimum on supply, with security patches back-ported across the Android and Linux firmware tracks and OTA infrastructure for pushing firmware and RKNN model updates to deployed units. Long-lifecycle programmes in industrial, signage and robotics usually ask for the term in writing, and it is written.

Can AndroidSBC ship custom boards to Amazon FBA warehouses or 3PL consolidation points?

Answer: Yes. AndroidSBC ships DDP to Amazon FBA warehouses in the US, EU and Japan, and to nominated 3PL consolidation points in Hong Kong, Singapore, Rotterdam, Los Angeles and Shenzhen. Carton labelling and pallet configuration follow FBA inbound requirements, the export declaration names the Wanlin Longgang source factory as the place of origin, and each pallet carries a per-unit barcode that traces back to the burn-in record for downstream RMAs.

How does AndroidSBC handle RMA or DOA replacements on custom boards?

Answer: Target DOA is 0.3 percent across twelve months. RMA works by returning the WF-C3588-S3 unit to Longgang with its burn-in barcode; replacements ship inside ten business days. Since each unit is traceable to its burn-in and configuration record, partners typically receive a root-cause note with the replacement rather than a silent credit.

Contact AndroidSBC: Start Your WF-C3588-S3 Sourcing Conversation

AndroidSBC is the export channel for the Wanlin WF-C3588 custom board line. Buyers in San Francisco and United States looking to source the WF-C3588-S3 straight from the source factory can use any of the following:

• Email: Androidsbc@163.com
• Export service hotline: +8613261677119
• Website: https://www.androidsbc.com
• Destination market file: FCC Part 15 authorisation with an FCC ID for radio modules and a UL or ETL listing for United States, administered by FCC / UL, entering at Port of Los Angeles on the Los Angeles to Yantian lane
• Source factory address: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China

The export desk asks for three things on a first enquiry: annual volume, customization scope and Incoterm. Provide those and a per-lot quote plus the WF-C3588 MOQ matrix comes back within two business days.